Detailinformationen

Teilenummer:

7N-5128

Mindestbestellmenge:

Hervorheben:

D6G Loader oil cooler

7N5128 oil cooler replacement

Diesel engine oil cooler part

Produkt-Beschreibung

7N-5128 Oil Cooler for D6G Loader

High-quality 7N-5128 diesel fuel injector specifically designed for optimal performance and fuel efficiency in D6G loader applications.

Product Specifications

Product Name	Fuel Injector
Part Number	7N-5128
Brand Name	JIAJUE
Model	D6G
Condition	Brand New
Availability	Rich Stock
Approximate Weight	1KG
Size (per unit)	20cm x 5cm x 8cm
Delivery Methods	DHL FedEx TNT UPS
Warranty	3 months
Shipment	Dispatched within 24-48 hours

Product Testing

Related Products

Frequently Asked Questions

Q1: How do I install my fuel injector after purchasing it?

Please refer to the "Step-by-Step Installation Guide" on our product details page, which contains detailed installation instructions for proper injector installation.

Q2: What precautions should I take before installing my fuel injector?

The installation environment must be dust-free; lubricate the O-ring with clean machine oil before installation to prevent oil leakage; and ensure the O-ring is installed correctly.

Q3: Why is my engine still unusable after replacing the fuel injector?

This is commonly due to air trapped in the high-pressure oil rail. Cycle the engine in short bursts (no more than 30 seconds) to purge air. It may take several attempts to stabilize pressure.

Q4: Is my device compatible with this part number of fuel injectors?

If you're unsure about compatibility, please send us your Engine Serial Number (ESN) for free verification.

Q5: How to determine if your fuel injectors need replacing?

Cylinder Cut-out Test: Using diagnostic software (ET), shut off cylinders one by one and observe engine speed fluctuations to locate faulty cylinders.
Fuel Rail Pressure Test: Check for internal leaks that prevent the system from building critical starting pressure.
Back-leakage Test: Excessive back-leakage indicates severe wear of internal control valve assembly.
Visual Inspection: Inspect fuel injector nozzles for carbon buildup, blockage, or corrosion.

Q6: How long will it take to receive my package after I make the payment?

Delivery time depends on your country, region, and customs clearance. Contact us with your address and postal code for shipping costs and estimated delivery time.

Step-by-Step Installation Guide

Pro-Tip: HEUI (Hydraulic Electronic Unit Injection) systems are extremely sensitive to contamination. A single speck of dust can cause premature failure.

1. Preparation: Clean the injector bores thoroughly. Ensure there is no carbon debris, old O-rings, or fuel/oil residue at the bottom of the seat. Inspect the injector sleeve for any signs of pitting or erosion.

2. Lubrication: Apply clean engine oil to the three O-rings and the backup rings. Never use grease. Only use clean engine oil to ensure the seals slide in without tearing.

3. Seating the Injector: Push the injector down firmly by hand until you feel it "seat." Install the hold-down clamp and bolt.

4. Torque Specifications: Tighten the bolt to 30 N⋅m±7 N⋅m (22 lb-ft). Note: Over-tightening can crack the injector body; under-tightening causes combustion gas leakage.

5. Trim Code Programming: Locate the 6-digit alphanumeric code on the top of the injector solenoid. Use ET (Electronic Technician) software to program this code into the ECM to ensure precise fuel delivery synchronization.

Troubleshooting Guide

Issue	Root Cause	Solution
Black Smoke	Poor spray atomization or stuck needle valve causing dripping	Inspect the air filter
Hard Start	Internal leakage in injector leading to insufficient starting oil pressure	Inspect injector O-rings and internal seals
Engine Misfire	Faulty solenoid valve coil or worn internal valve components	Inspect wiring harness connections and replace damaged injectors

Company Profile

Exhibition

Factory Environment

Packaging & Shipping

Product Video

7N-5128 7N5128 Oil Cooler for D6G Loader 8

Größe und Tag:

Herkunftsort:	China
Markenname:	JIAJUE
Modellnummer:	D6G

Min Bestellmenge:	1
Preis:	Please send mail or WhatsApp
Verpackung Informationen:	7N-5128 7N5128 Ölkühler für D6G-Lader wird je nach Kundenwunsch in einer Standard-Exportverpackung v
Lieferzeit:	1 Werktag
Zahlungsbedingungen:	L/C, D/A, D/P, T/T, Western Union
Versorgungsmaterial-Fähigkeit:	1000 Stück/Monat

7N-5128 7N5128 Oil Cooler for D6G Loader

D6G Loader oil cooler

7N5128 oil cooler replacement

Diesel engine oil cooler part

Dieselmotorkraftstoffinjektor,

-Brennstoffinjektoren,

Einheitspumpeninjektor

10R-1814 10R1814 Kraftstoffspritzer für C12-Motoren

10R-1256 10R1256 Kraftstoffspritzer für C12-Motoren

4903084 Treibstoffspritzer für den QSM11-Motor

21028884 Dieselbrennstoffspritzer für den D13D-Motor

557-7627 5577627 Treibstoffspritzer für die Baggermaschine E325D

0R-9530 Treibstoffspritzer 0R9530 Düse für C12-Motoren

0445 120 346 0445120346 Kraftstoffeinspritzer für die Maschine

0R-8684 0R8684 3126 Engine Diesel Fuel Injector